KAJIAN PENGARUH JENIS MATERIAL TERHADAP KUALITAS UKURAN PADA PROSES PENEKUKAN PELAT DENGAN METODA ANOVA
DOI:
https://doi.org/10.32722/pt.v20i3.3826Keywords:
Plates , measurements, bending processes, statisticsAbstract
Abstract
In previous research, it has been proven that the measurement technique, setting and use of quality measuring instruments can increase the quality of measurements during the bending process of steel plates (ST.37). However, this research has not examined the types of materials other than steel, even though other materials apart from ST.37, for example aluminum plates, brass plates and steel plates are widely used, especially in the manufacturing industry.. Therefore, the aim of this research is to analyze the effect of the type of material on the quality of the measurement in the bending process. This study uses an experimental method, combined with a theory that supports the discussion of the problem. The materials used are 3 different types of material plates (aluminum plate, brass plate and steel plate). The parameters observed include the measurement technique, setting and use of measuring instruments. Each material received 10 repetitions of the measurements. These three parameters were analyzed using ANOVA statistics, in order to determine the quality of the measurement of each material and the most dominant factors affecting the quality of the measurements.
Keywords: Plates, measurements, bending processes, and statistics.
Downloads
References
S. R. Schmid and K. Serope, Manufacturing enginering and technologi, Sixth. Singapore: Prentice hall, 2009.
Ambiyar and Purwantono, Fabrikasi logam. Padang: UNP Press, 2008.
Dadang, Teknik Dasar Pengerjaan Logam. Jakarta: Jakarta. Kementrian Pendidikan dan Kebudayaan, 2013. [Online]. Available: http://repositori.kemdikbud.go.id/id/eprint/10439
I. N. Sutarna et al., “Penerapan ergonomi pada proses pembuatan kotak alat untuk meningkatkan kinerja mahasiswa peraktik kerja pelat di bengkel teknologi mekanik politeknik negeri bali,” vol. 17, no. 1, pp. 31–35, 2017.
L. A. Meyer, Sheet metal shop practice, 4th ed. Chicago, USA: American technical society, 1975.
I. N. Sutarna, “Analisa penyebab penyimpangan ukuran pada proses penekukan pelat oleh mahasiswa di bengkel teknologi mekanik politeknik negeri bali,” Logic, vol. 15, no. 3, pp. 182–187, 2015.
S. Kalpakjian and S. Schmid, “Manufacturing engineering and technology, SI 6th Edition,” Pearson, p. 1216, 2013.
P. A. Cahyani, D. H. D. M.M., M.Pd, and D. Z. M.Pd, “Pengembangan jobsheet Pada mata kuliah kerja pelat di program studi pendidikan Teknik Mesin Universitas Sriwijaya,” J. Pendidik. Tek. Mesin, vol. 6, no. 2, pp. 143–150, 2019, doi: 10.36706/jptm.v6i2.7042.
A. D. Anggono, T. W. B. Riyadi, and W. A. Siswanto, “Dynamic explicit finite element code for U-bending simulation and springback prediction,” Appl. Mech. Mater., vol. 660, pp. 337–341, 2014, doi: 10.4028/www.scientific.net/AMM.660.337.
O. Diegel, Bend work the fine-art of sheet metal bending. Brakers press, 2002.
Ambiyar, Arwizet, and Nelvi, Teknik pembentukan pelat, vol. 8, no. 1. Jakarta: Direktotat Pembinaan Sekolah Menengah Kejuruan 2008, 2008.
I. E. Putra and K. A. K, “Desain Mesin Tekuk Plat Hidrolik Design of a Hydraulic Plate Bending Machine,” vol. 11, no. 2, 2021.
S. Sabarudin et al., “Desain Mesin Tekuk Plat Hidrolik Design of a Hydraulic Plate Bending Machine,” no. September, pp. 335–344, 2018.
S. Siregar, Metode penelitian kuantitatif. Jakarta: PT Fajar interpratama mandiri, 2013.
I. G. O. Pujihadi and I Ketut Widana, “Work position effects on physiological aspects of machining workers,” Manag. Educ. Eng., vol. 4, no. 1, pp. 1–23, 2016.
L. S. Meyers, G. C. Gamst, and A. J. Guarino, Performing data analysis using IBM SPSS. New Jersey: John Wiley & Sons, Inc, 2013.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Poli-Teknologi
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
