Perancangan Mesin Roll Plat Listrik sebagai Peningkatan Efisiensi Kerja di Industri Manufaktur


  • Fathan Mubina Universitas Buana Perjuangan Karawang
  • Amir Amir Universitas Buana Perjuangan Karawang



Mesin; Industri; Efisien


Several engineering companies in Indonesia still use conventional type machines which, when viewed from the point of view of maintenance, repair, and performance, are still far behind. More than that, we use automatic machines. The first step in this research is to find some related literature that supports it. Then observe the machine that roughly corresponds to the shape of the design later. Then make the design of the electric plate roll machine design. After the design is understood, then plan the equations needed in the analysis of this research. If it is known the equation that will be made when the data is obtained, it can be calculated immediately. The calculation is not adequate, there may be improper equation planning. The final step is when the calculation is done, the conclusion can be determined immediately. Based on the stages of the design process for the automatic system aluminum plate roller machine, several conclusions can be drawn for this final project, including for the roller machine itself using an asymmetric plate roller type with two high mill roll arrangements because this type of machine is the most popular plate roll machine simple


Obaidi, K. A., Xu, Y., & Valyrakis, M. (2020). The Design and Calibration of Instrumented Particles. Journal of Sensor and Actuator Networks, 1-18.

Riza, M. N. (2021). Mechanical Design & Analysis:High-Precision Microcontact Printhead for Roll-to-Roll Printing of Flexible Electronics. Massachusetts: Master of Science in Mechanical Engineering.

Eliasson, S., & Fransson, A. (2021). Design and evaluation of a test rig formeasuring gear related losses within aVolvo Trucks gearbox. Gothenburg: Chalmers University of Technology.

Ellitan, L. (2020). Competing in the Era of IndustrialRevolution 4.0 and Society 5.0. Jurnal Maksipreneur: Manajemen, Koperasi, dan Entrepreneurship, 1-12.

Vincze, G., Simoes, F. J., & Butuc, M. C. (2020). Asymmetrical Rolling of Aluminum Alloys andSteels: A Review. metals, 1-24.

Marinelli, G., Martina, F., Ganguly, S., & Williams, S. (2020). Grain Refinement in an Unalloyed Tantalum Structure by Combining Wire + Arc Additive Manufacturing and Vertical Cold Rolling. Additive Manufacturing, 1-19.

Ekholm, K. H. (2020). Popular Instructional Design Models: Their Theoretical Roots and Cultural Considerations. International Journal of Education and Development using Information and Communication Technology (IJEDICT), 50-65.

Pilkey, W. D. (2021). Stress Concentration Factors. Toronto: A Wiley-Interscience Publication.

Fitriani, D., Rasyid, Y., & Dewanti, R. (2020). Need Analysis on Developing Essay Teaching Material base on Brainwriting Strategy. International e-Journal of Educational Studies (IEJES), 81-92.

Moshrefzadeh, A. (2021). Condition monitoring and intelligent diagnosis of rolling element bearings under Constant/Variable Load and Speed . journal of Mechanical Systems and Signal Processing, 1-36.

Mulay, A., Ben, B. S., Ismail, S., & Kocanda, A. (2019). Prediction of Average Surface Roughness and Formability in Single Point Incremental Forming using Artificial Neural Network. Archives of Civil and Mechanical Engineering 19, 1135-1149.

Gonzalez, A. S., Battaglia, P., Xu, R., Cranmer, K., Cranmer, M., Spergel, D., & Ho, S. (2020). Discovering Symbolic Models from Deep Learning with Inductive Biases. Conference on Neural Information Processing Systems (NeurIPS 2020) (hal. 1-25). Vancouver: Arxiv.

Jeyan, J. M., Chhetri, R. T., Thota, P. S., Shrestha, P., & Pasha, S. S. (2021). Design and development of a tri-pro UN manned. JETIR, 2459-2473

Arango, I., & Alzate, S. M. (2020). Numerical Design Method for CVT Supported in Standard Variable Speed Rubber V-Belts. Applied Sciences, 1-23.

Asabin, V., Roslyakov, A., Kurmanova, L., Petukhov, S., & Erzamayev, M. (2019). Conversion of Diesel Locomotive Engines to Operation on Natural Gas Motor Fuel. KTTI (hal. 1-11). Samara: E3S Web of Conferences.

Lv, J., Wang, Z., & Ma, S. (2020). Calculation Method and Its Application for Energy Consumption of Ball Mills in Ceramic Industry. Advances in Applied Ceramics, 1-13

Singh, A. K., Singh, A. K., & Yadav, R. P. (2020). Stress Intensity Factor of Dynamic Crack in Double-Layered Dry Sandy Elastic Medium due to Shear Wave under Different Loading Conditions. ASCE, 1-14.

Aas, I. M. (2021). Evaluation Tool for Dimensioning Off-Grid Solar Power Systems. Gothenburg: Chalmers University of Technology.

Cragg, C. H., Graf, J. C., & Hobbs, A. (2021). Risk Reduction of Orion Multi-Purpose Crew Vehicle (MPCV) Program Government-Furnished Equipment for Environmental Control and Life Support (ECLS). Houston: NASA Engineering & Safety Center.

Ampuja, R. (2021). Design of A Wire Electric Discharge Machine. Toukokuu: Mechanical Engineering Production Technology.



How to Cite

Mubina, F., & Amir, A. (2022). Perancangan Mesin Roll Plat Listrik sebagai Peningkatan Efisiensi Kerja di Industri Manufaktur. Jurnal Mekanik Terapan, 3(1), 18–25.