Characteristics Of Liquid Products Co-Pyrolysis Plastic Waste and Used Lubricants

Authors

  • Dede Muhamad Ilyas Ilyas Politeknik Negeri Jakarta
  • Dianta Mustofa Kamal Politeknik Negeri Jakarta
  • Shafa Amatullah Fatin Politeknik Negeri Jakarta
  • Iwan Susanto Politeknik Negeri Jakarta
  • Sonki Prasetya Politeknik Negeri Jakarta

DOI:

https://doi.org/10.32722/pt.v23i2.4997

Abstract

The increasing usage of plastic is proportional to the amount of plastic waste today. The plastic usage makes the human live easier especially for packaging purposes. However, it also has a negative impact to the environment. This is due to it cannot easily decompose. Therefore, it can reduce the level of soil fertility. Besides plastic, lubricant waste from motor vehicles can induce an environmental problem as well since it is categorized of hazardous material (B3) waste. Currently, the use of plastic waste has been widely carried out by correlating into liquid fuel through thermal cracking or pyrolysis treatment. It produces liquid and it can be used as an alternative liquid fuel. This study uses the co-pyrolysis method for treating the used plastic waste with used lubricants. The composition ratios used are 10:0, 10:2, 10:4, 10:6, and 10:8. The highest acquisition of liquid products was in the composition ratio of 10:6 as much as 24.67% with a calorific value of 11015.33 cal/g. Then the highest calorific, density, and viscosity values were obtained, namely at the 10:8 composition ratio of 11061.67 cal/g, 0.8906 g/mL, and 0.927 cSt. It was concluded that the mixing of used lubricants in the co-pyrolysis of LDPE plastic waste was able to increase the calorific value of the liquid product produced.

Downloads

Download data is not yet available.

References

H. G. Shebu, B. T. Asfaw, S. A. Yiman, and D. E. Manyazewal, “A Review on Extraction of Liquid Fuel From Waste Plastic,” J. Pet. Eng. Technol., vol. 9, no. 3, pp. 34–40, 2019.

Y. G. Wibowo and A. Izzuddin, “Integrasi Pengolahan Sampah Metode 3R Dengan Bank Sampah Di SMA,” J. Pengabdi. Masy. Manag., vol. 2, no. 1, pp. 19–23, 2021.

D. Iswadi et al., “Pemanfaatan Sampah Plastik Ldpe Dan Pet Menjadi Bahan Bakar Minyak Dengan Proses Pirolisis,” J. Ilm. Tek. Kim., vol. 1, no. 2, pp. 77–85, 2017, [Online]. Available: http://openjournal.unpam.ac.id/index.php/JITK/article/view/718.

K. Eldwita, S. D. Lestari, E. S. A, and Fatria, “Pengaruh Jumlah Katalis dan Temperatur Pada Produksi Bahan Bakar Cair Dari Ban Bekas Dengan Metode Perengkahan Katalik,” J. Kinet., vol. 11, no. 2, pp. 19–25, 2020.

A. Rafi, P. Hartono, and Margianto, “Analisis Energi Terbrukan Pada Proses Pirolisis Dengan Memanfaatkan Sampah Plastik,” J. Tek. Mesin, no. Vol 12, No 01 (2019): Jurnal Teknik Mesin, p. 30, 2019, [Online]. Available: http://riset.unisma.ac.id/index.php/jts/article/view/3024.

M. Syamsiro, M. A. Saputro, J. Winarno, B. Megaprastio, and Z. Mufrodi, “Studi Co-pirolisis Plastik HDPE dan Oli Bekas Menjadi Bahan Bakar Cair Alternatif,” deHAP 2021, vol. 1, no. 1, pp. 331–337, 2021.

Azharuddin, A. A. Sani, and M. A. Ariasya, “Proses Pengolahan Limbah B3 (Oli Bekas) Menjadi Bahan Bakar Cair dengan Perlakuan Panas yang Konstan,” J. Austenit, vol. 12, no. 2, pp. 48–53, 2020.

F. Abnisa and W. M. A. Wan Daud, “A review on co-pyrolysis of biomass: An optional technique to obtain a high-grade pyrolysis oil,” Energy Convers. Manag., vol. 87, pp. 71–85, 2014, doi: 10.1016/j.enconman.2014.07.007.

Wijaya, H. S. Jaya, and Wigoyo, “Perbandingan Hasil Penyulingan Plastik Tipe HDPE dan LDPE Dengan Alat Penyulingan Sederhana,” STEAM Eng., vol. 3, no. 1, pp. 39–45, 2021.

Z. Mufrodi, M. A. Saputro, J. Winarno, B. Megaprastio, and M. Syamsiro, “Produksi Bahan Bakar Minyak Alternatif Dari Pirolisis Plastik Polipropilen dan Oli Bekas,” deHAP 2021, vol. 1, no. 1, pp. 317–325, 2021.

U. B. Surono and Ismanto, “Pengolahan Sampah Plastik Jenis PP, PET, dan PE Menjadi Bahan Bakar Minyak dan Karakteristiknya,” J. Mek. dan Sist. Therm., vol. 1, no. 1, pp. 32–37, 2016.

Y. Bow and S. R. . Sihombing, “PENGOLAHAN Sampah Low Density Polyethylene (Ldpe) Dan Polypropylene (Pp) Menjadi Bahan Bakar Cair Alternatif Menggunakan Prototipe Pirolisis Thermal Cracking,” J. Kinet., vol. 9, no. 3, pp. 1–6, 2018.

R. P. Liestiono, M. S. Cahyono, W. Widyawidura, A. Prasetya, and M. Syamsiro, “Karakteristik Minyak dan Gas Hasil Proses Dekomposisi Termal Plastik Jenis Low Density Polyethylene (LDPE),” J. Offshore Oil, Prod. Facil. Renew. Energy, vol. 1, no. 2, p. 1, 2017, doi: 10.30588/jo.v1i2.288.

M. Jahiding, E. Nurfianti, E. S. Hasan, R. S. Rizki, and Mashuni, “Analisis Pengaruh Temperatur Pirolisis Terhadap Kualitas Bahan Bakar Minyak Dari Limbah Plastik Polipropilena,” Gravitasi, vol. 19, no. 1, pp. 6–10, 2020.

Departemen ESDM, “Standar Mutu (Spesifikasi) Bahan Bakar Minyak Jenis Minyak Bakar Yang Dipasarkan Dalam Negeri,” Jakarta, 2008.

T. B. Prasetiyo and F. Rhohman, “Karakteristik Hasil Proses Pirolisis Jenis Plastik PET, HDPE, dan PP Menggunakan Katalis Alam Metode SPSS dan Matlab,” SEMNAS Inov. Teknol., vol. 1, no. 1, pp. 325–330, 2021.

J. Waluyo, A. P. Perkasa, and D. Ramadhana, “Pirolisis Sampah Plastik HDPE Sebagai Alternatif Pengganti Kerosin Dengan Menggunakan Katalis Zeolit Alam,” Equilibrium, vol. 3, no. 1, pp. 34–40, 2019.

D. G. . Adoe, W. Bunganaen, I. F. Krisnawi, and F. A. Soekwanto, “Pirolisis Sampah Plastik PP (Polypropylene) Menjadi Minyak Pirolisis Sebagai Bahan Bakar Primer,” J. Tek. Mesin Undana, vol. 3, no. 1, pp. 17–26, 2016, [Online]. Available: http://ejournal-fst-unc.com/index.php/LJTMU.

R. Nazif, E. Wicaksana, and Halimatuddahliana, “Pengaruh Suhu Pirolisis Dan Jumlah Katalis Karbon Aktif Terhadap Yield Dan Kualitas Bahan Bakar Cair Dari Limbah Plastik Jenis Polipropilena,” J. Tek. Kim., vol. 5, no. 1, pp. 49–55, 2016.

O. S. Mazdhatina, A. Setiawan, and V. Setiani, “Pengaruh Katalis Zeolit Alam terhadap Karakteristik Minyak Pirolisis Sampah Plastik PP (Polypropylene),” Conf. Proceeding …, no. 2623, pp. 87–90, 2020, [Online]. Available: http://103.24.48.75/index.php/CPWTT/article/view/1711.

Downloads

Published

2024-05-31

How to Cite

Ilyas, D. M. I., Mustofa Kamal, D., Amatullah Fatin, S., Susanto, I., & Prasetya, S. (2024). Characteristics Of Liquid Products Co-Pyrolysis Plastic Waste and Used Lubricants. Jurnal Poli-Teknologi, 23(2), 55–61. https://doi.org/10.32722/pt.v23i2.4997

Issue

Section

Articles

Most read articles by the same author(s)