ANALISIS DAYA DUKUNG PONDASI TIANG BOR PADA PROYEK TOL SERANG-PANIMBANG

##plugins.themes.academic_pro.article.main##

Dinah Faidah
Putra Agung Maha Agung

Abstract

The pile foundation serves to carry and hold the load on it, namely the load on the superstructure. Each foundation must be able to support loads up to a predetermined safety limit, including supporting the maximum load that may occur in the Serang–Panimbang Toll Development Project. The location under review is the head of the bridge overpass 23. The purpose of this study was to determine the axial bearing capacity, lateral bearing capacity and foundation settlement. Based on the results of the analysis of the bearing capacity of the drill pile on the head of the bridge overpass 23 Serang-Panimbang toll road which is planned with a configuration of 5 poles with a diameter of 0.8 m, the distance between drill piles is 2.5D, a depth of 17 m, obtained an Axial carrying capacity of 54.42 tons for a single drill pile and 235.69 Tons for group drill piles based on the Skempton method. Meanwhile, the lateral bearing capacity obtained is 82.25 tons for single drill pile clamping conditions and 356.17 tons for group drill piles using the Broms method. The horizontal deflection due to static load is 3.8 mm and 6 mm due to dynamic load. The decrease in the single drill pile that occurred was 6.93 mm and 3.69 mm for the group drill pile. Based on the calculation of the stability of the configuration, it is said to be stable to withstand the working load.

##plugins.themes.academic_pro.article.details##

References

  1. R. Gunawan, Pengantar Teknik Fondasi, vol. 1999, no. December. Yogyakarta: Kanisius, 2006.
  2. H. C. Hardiyatmo, Teknik Pondasi 2, 4th ed. Yogyakarta: Universitas Gadjah Mada, 2008.
  3. M. Dr. Ir. Abdul Hakam, “REKAYASA PONDASI Untuk Mahasiswa Dan Praktisi,” no. April 2008, p. 240, 2008.
  4. B. M. Das, Principles of Foundation Engineering (Seventh Edition). Stamford: Cengange Learning, 2011.
  5. I. W. A. Basoka, “Perbandingan Daya Dukung Tiang Pancang Berdasarkan Pengujian Cone Penetration Test (CPT) Dan Standard Penetration Test (SPT) Pada Tanah Berpasir,” Mapp. Landslide Susceptible Zo. by Using Freq. Ratios Bluncong, vol. 5, no. 1, pp. 126–141, 2020.
  6. N. D. Hendrik Prama A., Yusep Muslih P., “PERBANDINGAN ANALISIS KAPASITAS DUKUNG TIANG TUNGGAL PONDASI MINIPILE MENGGUNAKAN RUMUS DINAMIK, HASIL UJI SPT DENGAN HASIL UJI PDA,” pp. 570–577, 2015.
  7. Badan Standardisasi Nasional, SNI 4153:2008 Cara Uji Penetrasi Lapangan dengan SPT. 2008.
  8. A. P. dan A. Nadira, “PERENCANAAN DAYA DUKUNG PONDASI BORED PILE PADA PROYEK TRANSPARK CIBUBUR,” 2019.
  9. S. Long, A. Iskandar, and S. Leman, “ANALISIS DAYA DUKUNG TIANG BOR AKSIAL, LATERAL, DAN PENURUNAN PADA TANAH CLAY SHALE DI SENTUL, BOGOR,” JMTS J. Mitra Tek. Sipil, vol. 2, no. 3, pp. 125–134, 2019.
  10. M. Munir and Y. A. Yakin, “Evaluasi Deformasi dan Stabilitas Struktur Tiang Pelat (Pile Slab) di Atas Tanah Gambut (Studi Kasus: Ruas Jalan Tol Pematang Panggang - Kayu Agung, Provinsi Sumatera Selatan) (Hal. 105-116),” RekaRacana J. Tek. Sipil, vol. 4, no. 3, p. 105, 2018, doi: 10.26760/rekaracana.v4i3.105.
  11. M. Munawaroh, “ANALISIS DAYA DUKUNG LATERAL KELOMPOK TIANG PONDASI BORED PILE PADA PROYEK PEMBANGUNAN FLY OVER MARTADINATA BOGOR,” J. Online Mhs. Bid. Tek. …, pp. 1–12, 2020.
  12. B. B. Broms, “Lateral Resistance of Piles in Cohesionless Soils,” J. Soil Mech. Found. Div., vol. 90, no. 3, pp. 123–156, 1964, doi: 10.1061/jsfeaq.0002132.
  13. Badan Standardisasi Nasional, SNI 8460-2017 Persyaratan Perancangan Geoteknik, vol. 8460. 2017.
  14. A. Kristianto, N. S. Surjandari, and N. Djarwanti, “ANALISIS DEFLEKSI LATERAL TIANG TUNGGAL FREE-END PILE PADA TANAH KOHESIF,” no. 36, pp. 615–622, 2017.
  15. K. Terzaghi and R. B. Peck, “Mekanika Tanah Dalam Praktek Rekayasa,” Penerbit Erlangga, vol. 2, pp. 1–373, 1987.
  16. J. E. Bowles, “Analisis Dan Desain Pondasi II,” Erlangga, Jakarta, vol. 2, p. 474, 2005.
  17. H. C. Hardiyatmo, Analisis dan Perancangan Fondasi II. Yogyakarta: Universitas Gadjah Mada, 2011.
  18. Badan Standardisasi Nasional, SNI 1725:2016 Standar Pembebanan untuk Jembatan. 2016.