PENGARUH ALKALI SILIKA REAKTIF PASIR TERHADAP KUAT TEKAN MORTAR RENDAMAN

##plugins.themes.academic_pro.article.sidebar##

Published Apr 17, 2023
https://doi.org/10.32722/cmj.v5i1.4773
Download
PENGARUH ALKALI SILIKA REAKTIF PASIR TERHADAP KUAT TEKAN MORTAR RENDAMAN
Statistic
Vol. 5 No. 1 (2023): Construction and Material Journal Vol. 5 No. 1 Maret 2023

##plugins.themes.academic_pro.article.main##

Mudiono Kasmuri
Politeknik Negeri Jakarta
Ajeng Ayuningtias
Politeknik Negeri Jakarta

Abstract

Mortar is a building material made of cement, fine aggregate, and water. To get a good mortar strength, the properties, and characteristics of each of the mortar constituents must also be studied further. Aggregates containing silica can be reactive or non-reactive to alkaline elements in cement. The purpose of this study was to determine the effect of alkaline silica reactive sand on the compressive strength and flexural strength of mortar immersed in seawater. This research uses an experimental method, namely Rangkas sand, Bangka sand and Lumajang sand which have gone through the XRF (X-Ray Fluorescence) testing process to determine the percentage of compound content contained. The research method to determine the reactivity of the sand refers to ASTM C 1260. The compressive strength and flexural strength of the mortar were tested with two variations of immersion, namely by using fresh water and sea water. The immersion of the mortar was carried out for 7, 14, 28 and 56 days. From the results of testing the compressive strength and flexural strength of mortar at the age of 28 days had the same results for fresh water and seawater immersion, namely sand with high potential for reactive alkali silica has low compressive strength and flexural strength values ​​for all types of immersion. The freshwater immersion method has been used to test the mortar's flexural and compressive strength. It has a higher compressive and flexural strength value than the seawater immersion mortar, with a percentage ratio of 27.1% of compressive strength and 17.3% of flexural strength in mortar, with an immerse age of 28 days.

##plugins.themes.academic_pro.article.details##

References

  1. A. Syukroni, Sifat Fisik dan Mekanik Mortar Polimer dengan Variasi Resin 5%; 15%; 20% dan 25%. 2013.
  2. A. P. Sihombing, Y. Afrizal, and A. Gunawan, “Pengaruh Penambahan Arang Batok Kelapa Terhadap Kuat Tekan Mortar,” Inersia, J. Tek. Sipil, vol. 10, no. 1, pp. 31–38, 2018, doi: 10.33369/ijts.10.1.31-38.
  3. Nadia and A. Fauzi, “Pengaruh Kadar Silika Pada Agregat Halus Campuran Beton Terhadap Peningkatan Kuat Tekan,” Kontruksia, vol. 3, no. 1, pp. 35–43, 2011.
  4. N. M. Labib, A. Setyawan, and A. Sumarsono, “Analisis Reaksi Alkali Silika Agregat Terhadap Kuat Tekan Dan Kuat Lentur Beton Untuk Perkerasan Kaku Yang Tahan Terhadap Air Laut,” e-Jurnal MATRIKS Tek. SIPIL, vol. 4, no. 2, pp. 602–609, 2016.
  5. ASTM C 1260 – 07, “Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method),” West Conshohocken, PA ASTM, vol. 04, no. October 2001, pp. 1–5, 2010, [Online]. Available: https://compass.astm.org/download/C1260.36913.pdf
  6. ASTM C230, “Standard Specification for Flow Table for Use in Tests of Hydraulic Cement 1,” Annu. B. ASTM Stand., pp. 4–9, 2010.
  7. M. Isneini and S. Brojonegoro, “Pemanfaatan Mineral Tambahan Untuk Reduksi Ekspansi Akibat Reaksi Alkali Silika,” vol. 1, pp. 251–255, 2018.
  8. S. Zuraidah and B. Hastono, “Pengaruh Variasi Komposisi Campuran Mortar Terhadap Kuat Tekan,” Ge-STRAM J. Perenc. dan Rekayasa Sipil, vol. 1, no. 1, pp. 8–13, 2018, doi: 10.25139/jprs.v1i1.801.
  9. SNI 03-6825-2002, “Metode pengujian kekuatan tekan mortar semen Portland untuk pekerjaan sipil,” Bandung Badan Stand. Indones., pp. 1–9, 2002.
  10. SNI 03-4154-1996, “Metode Pengujian Kuat Lentur Beton dengan Balok Uji Sederhana yang Dibebani Terpusat Langsung,” Badan Stand. Nas., vol. 26, no. 4, pp. 551–556, 1996.
  11. M. C. Damayanti, N. Rauf, and E. Juarlin, “Pengaruh Perendaman Air Laut Terhadap Kualitas Mortar Semen The Influence of Sea Water Immersion Concerning Quality of Mortar Cement,” pp. 5–8, 2014.